How do Mud Flaps Install on my 2019 Ram 3500?

Question

Question:

What is the recommended installation procedure for mud flaps #337B1218LSP on a 2019 Ram 3500

asked by: Steve B

1

Helpful Expert Reply:

The Buyers Products Mud Flaps part # 337B1218LSP do not have a specific installation process as this is something that is more of a universal fit.

On your 2019 Ram 3500 you would trim the flap to fit the contour of your fender well and attach it to the steel that runs around the inner edge of the fender using fasteners of your choice (self tapping screws or machine bolts and nuts).

For a custom fit application I recommend using the WeatherTech Mud Flaps part # WT110108-120108 this is thefront and rear custom fit set for your truck. They will install without drilling or modifying your truck and are very durable and rugged. These do have actual instructions for their installation and are linked for you to check out.

expert reply by: Randy B

1

Answer 1

The Buyers Products #337B1018LSP do not come with any mounting hardware, since the method of mounting is going to vary from vehicle to vehicle. Ideally you will use the factory fasteners on your vehicle to secure it into place and locally sourced…

view full answer...

Answer 2

The Replacement Pivot Arm "A" #BW3035A you found will fit on either the left or right hand side of your B&W Companion Base #BWRVB3500. You will need a Replacement Pivot Arm "B" #BW3035B for the opposite…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, the Buyers Products front mud flaps part #337B1018LSP are a front set of flaps that fits your 2004 Jeep TJ Wrangler.

view full answer...

Answer 5

The correct replacement key for your etrailer Hitch Receiver Lock #e98881 with key code 029 would be Replacement Key for etrailer Hitch and Coupler Locks #e75UR.

view full answer...

Answer 6

Yes, the Aries RidgeStep Running Boards will fit your 2023 Ford Transit T250. The #AAC3696 is just the running boards so you will need the #AA56FR which includes the custom mounting kit.

view full answer...

Answer 7

Yes you can go the route you mentioned. You'd need to install an idler Dexter 8k Nev R Lube hub with part #004-402-90 on your spindles and then you could use a slip on kit like the part #K2R89DDE and you'd be set.

view full answer...

Answer 8

The height setting you'll need to use when installing the Curt A16 head part #C16520 that you referenced is going to be based on what your trailer needs to sit level. The height of the head is adjustable as well as how the pin box attaches to the…

view full answer...

Answer 9

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 10

The Curt #C16521 5th wheel hitch you mentioned is indeed height adjustable from 17-1/2 to 21-1/2 inches in height. Some of the bed sides on todays trucks are pretty tall (like the Ford F Series), so the hitch heights needed to increase as well. To…

view full answer...

Answer 11

So the lifespan and when to change a lube plate doesn't have a hard and fast answer because there are numerous variables associated with how long it will last. The terrain you are going over, the weight of your trailer, and the frequency with…

view full answer...