Replacement Pin To Hold Gate Of Utility Trailer

Question

Question:

Im looking for the chained clip/pins that hold my front and rear gates on this brand of utility trailer. Or this something I should make from local pieces/parts? Snowbear Utility trailer gate clips/chains

asked by: David A

0

Expert Reply:

I recommend to use Bolt-On Stainless Steel Spring Latch pins part # SL716SS that can be bolted to the utility trailer to keep the gate closed. At this time we do not carry the clip/pin with chain for the gates on your Snowbear utility trailer. I have attached a photo of an example.

expert reply by: Heather A

0

click to enlarge

Answer 1

We have a large selection of spring door latches available, such as the excellent Penloc Heavy Duty Spring Latch #F720-282U108. This spring features bracket dimensions of 3 inches long and 1-1/4 inches wide. It has a mounting hole diameter of 5/16…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that you'll have…

view full answer...

Answer 4

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 12

Yes, the Kenda Karrier ST175/80R13 Radial Trailer Tire #AM31990 will indeed fit on the etrailer Hitch Mounted Spare Tire Carrier #e98ZR. The spare tire carrier will work with virtually any 4 lug, 5 lug or 6 lug wheel. The #AM31990 wheel uses the…

view full answer...

Replacement Pin To Hold Gate Of Utility Trailer

Product Page this Question was Asked From

Continue Researching