Recommended Trailer Hitch for a 2003 Ford E-450 Cab and Chassis

Question

Question:

I have a 2003 e 450 motorhome Need hitch for it, with at least 500 or more tongue weight

asked by: Andy B

0

Expert Reply:

The best option we have for a 2003 Ford E-450 Cab and Chassis is the B&W Heavy-Duty Trailer Hitch Receiver part # BWHDRH25198 which has a 1,600 lb tongue weight capacity so it will be plenty for your needs. That said, there are no exact fit trailer hitches for a motorhome so what you need to do is make sure the body doesn't hang down more than 5" below the bottom of the frame and that the frame rails are 34" apart outside to outside.

expert reply by: Conner L

0

Answer 1

We do offer a B&W hitch for your 2000 Chevy C/K Series truck. Due to the frame width you mention, you'd want to use the B&W Class V hitch, part #BWHDRH25124 which is designed for pickup trucks. The B&W Class V receiver hitch you…

view full answer...

Answer 2

Yes, check out the picture I attached that has the vertical distances from where the hitch mounts to the frame of the vehicle down to the hitch tube. Since you need at least 6 inches this would clear that by 1-3/8 inches.

view full answer...

Answer 3

The side brackets of the Curt hitch part #C14082 are 9-3/4 inches long so you'd have the clearance needed to fit this on your frame since you have 10 available inches.

view full answer...

Answer 4

The Adjustable Width Trailer Hitch Receiver for RVs part #C13702 will be a much better option for you than the Draw-Tite Max-E-Loader Trailer Hitch Receiver part #41522. The Draw-Tite Max-E-Loader Trailer Hitch Receiver is designed specifically for a…

view full answer...

Answer 5

I spoke with my contact at B&W about your 1996 Ford F-250 Powerstroke. They were unable to tell me anything about the Luverne 8 inch bumper you have on your F-250 but did offer some other advice. The trailer hitch designed to fit your truck I…

view full answer...

Answer 6

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes- 29-1/2"…

view full answer...

Answer 7

It sounds like you've got the deep drop bumper on your 1996 Ford F-350, so the correct B&W Class V hitch for your truck is the #BWHDRH25198. It sounds like they potentially got you the #BWHDRH25122 to start, which is for use on the standard…

view full answer...

Answer 8

I have attached a photo of the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25198 you asked about. I have noted the mounting holes on the photo you can check out. The distance center-to-center from the front mounting hole to the second is…

view full answer...

Answer 9

Yes, as noted in our fit guide the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 is only a fit for the cab and chassis models with 34 inch frames of 1991 Chevy truck. Assuming you have a standard bumper, the correct trailer hitch for your…

view full answer...

Answer 10

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 11

For your 1996 Chevy K2500 with a step bumper the B and W Hitch part #BWHDRH25124 is a confirmed fit. The distance between the mounting holes left to right is 34-1/2 inches. The spare will need to be temporarily moved to install this but it will be…

view full answer...

Answer 12

The B and W Hitch part #BWHDRH25122 would fit your 1995 Chevy Silverado 3500 if it was built on a cab and chassis model. Which easy way to determine this is to measure the truck frame from outside to outside. If this measurement is 34 inches then you…

view full answer...

Recommended Trailer Hitch for a 2003 Ford E-450 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching