Torklift Camper Tie Downs that Fit 1999 Ford F-250 Long Bed with Running Boards and Factory Hitch

Question

Question:

Have 1999 ford f250 superduty 8foot bed with running boards and I think factory installed rear hitch. Which model do I need for front and back tie downs

asked by: Tim W

0

Expert Reply:

The correct Torklift Tie Downs you'd need for your 1999 Ford F-250 long bed, with running boards and a factory hitch is the part # TLF4006 and # TLF3001.

expert reply by: Jameson C

0

Answer 1

Since your F-250's hitch was installed after it left the factory it could potentially be either a factory hitch or an aftermarket hitch. There should be a safety sticker on the hitch that indicates its capacities and also its manufacturer. If…

view full answer...

Answer 2

When determining if rear Torklift tie-downs are available for your 2006 Ford F-350 Super Duty, it truly depends on your bed length, what hitch model you have installed (if any), or if you have a board/step underneath your truck. For example, if you…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

The best air bag kit for your 2022 Ford F-350 that has a single rear wheel axle is the part #F95FV which has the 5,000 lb capacity you are wanting. Firestone bags are superior Air Lift bags. The ply rating of the rubber is higher, the attachment to…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 12

You'll need to do some slight measuring to ensure the fit of the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV on your 4WD 2022 Ford F-350 FX4 dually. Just measure from the top of the rear axle to the top of the jounce…

view full answer...

Torklift Camper Tie Downs that Fit 1999 Ford F-250 Long Bed with Running Boards and Factory Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching