Compatibility of TorkLift Camper Tie-Downs

Question

Question:

what is the square tube size for a tlf3001 and tlf3004? i have a 2004 f250 SD with a ford oem hitch, which was added quite a few years later and dont know what year truck its from. there i need to know the tube size with one of the above units will fit. thanks

asked by: Jeff W

0

Expert Reply:

Since your F-250's hitch was installed after it left the factory it could potentially be either a factory hitch or an aftermarket hitch. There should be a safety sticker on the hitch that indicates its capacities and also its manufacturer. If there is no such sticker on your hitch, nor any identification for brand (Curt, Draw-Tite, Hidden Hitch) nor a part number, then chances are its the OEM version.

If you have a non-Torklift aftermarket hitch the tie downs you can use are part # TLF2011 and TLR3500. If you have the factory hitch use parts # TLF2011 and # TLF3001.

My contact at TorkLift confirmed both tie downs use the same 2-inch steel tubing.

expert reply by: Adam R

0

Answer 1

Yes, the inside dimensions of the entire length of the Tow Ready Combo Bar #80948 that you referenced is 2 inch by 2 inch.

view full answer...

Answer 2

The Roadmaster Anti-Rattle Hitch Extender for Tow Bars - 2" Hitches - 7-3/4" #RM-071-1075 has a maximum tongue weight of 400 pounds. The tongue weight is the downward force that the trailer exerts on the hitch. If you are looking for the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Compatibility of TorkLift Camper Tie-Downs

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching