Red and Amber 2-1/2 Inch Round LED Trailer Lights with Grommet and Plug

Question

Question:

Could you please quote: Optronics 2-1/2" Amber 3 diode LED Marker Light 12-24 volt Optronics 2-1/2" Red 3 diode LED Marker Light 12-24 volt A57GB Recess Mount Grommet open back A46PB Straight PL10 Plug 6" lead I have spoken to Optronics and they say that Etrailer have full access to their range.

asked by: Rod G

0

Expert Reply:

We can get you set up with red and amber clearance lights, grommets, and plugs for your trailers (the prices can be seen on the product pages). The red clearance lights are compatible with either 12 volt or 24 volt systems, though when I spoke with Optronics they told me the matching amber lights are obsolete, which means there are only 12 volt amber LED clearance lights. Here are the parts you will need:

- LED Clearance or Side Marker Light - Submersible - 3 Diodes - Red Lens - 12V/24V # OPT94FR

- Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Round - Amber Lens # MCL57AB

- Rubber Grommet for 2-1/2" Round Trailer Lights - Recessed Mount - Open Back # A57GB

- 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead # A46PB

Additionally I have added links to video reviews for you to take a look at.

expert reply by: Kyle S

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Red and Amber 2-1/2 Inch Round LED Trailer Lights with Grommet and Plug

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching