Can Head On Lippert Electric Trailer Jack Be Rotated to Gain Clearance For Tailgate

Question

Question:

is it possible to rotate the head unit 90 deg on a Lippert LC285318.Doing this would allow the tailgate to be opened with trail attached.

asked by: Mike

1

Helpful Expert Reply:

I do have a solution for you, however just the head itself on the Lippert Electric Trailer Jack # LC285318 cannot be rotated.

To gain clearance between it and the tailgate on your truck your best option is to simply use a longer ball mount. Something like the Curt # D-26, which measures 12-5/8" long from the hitch pin hole to the ball hole, would work well to increase space between the truck and trailer connection so that you can lower your tailgate.

I have attached a short video review below on this particular ball mount and a link that will take you to our complete selection of longer models that you can look through.

expert reply by: Chris R

1

Answer 1

Friction sway control units like the part #83660 require drilling into the frame of the trailer for installation. You would need to contact the manufacturer of your trailer to determine if they are okay with you doing that on your trailer. Most…

view full answer...

Answer 2

If the plate of your old sway control system interferes with the installation of the dual cam sway control of the Strait-Line Weight Distribution System #RP66087 then it will need to get removed. The additional bolt holes should not affect the…

view full answer...

Answer 3

You can rotate the whole trailer jack, such as #LC285318 or another A-frame mount jack, by unbolting it from the trailer, turning it, and bolting it back on. You would not be able to rotate just the head by itself.

view full answer...

Answer 4

Since the instructions for the Blue Ox SwayPro Weight Distribution #BXW1000 state that any air-ride shock absorbers, air springs, or automatic leveling systems need to be disabled or deflated to the manufacturer's minimum recommended pressure…

view full answer...

Answer 5

I would recommend that Blue Ox TrackPro #BLU77FR simply because it does not have lift chains like the SwayPro #BXW1006. Both will do a great job but the TrackPro will have a little less movement because of the absence of drop chains. Blue Ox is a…

view full answer...

Answer 6

With your Blue Ox SwayPro Weight Distribution w/ Sway Control #BXW1500 the rough ride and bucking could be from a couple of variables. If you have weight behind the rear axle of your truck, you may need a larger weight distribution system because…

view full answer...

Answer 7

I spoke with my contact at Lippert regarding the Electric Trailer Jack with Footplate #LC285318 referenced in your question. For this jack they recommend 26 ft lbs of torque for the hardware that will hold the jack to your trailer. This is a very…

view full answer...

Answer 8

The difference between the two systems is basically the attachment point. One is not better than the other except that the trunnion bars are a little easier to install than the round bars that require a clip to hold them into the head. For the round…

view full answer...

Answer 9

The Lippert Components Power Tongue Jack #LC285318 uses a standard 3-bolt a-frame type mounting scheme. It is designed to be installed in a specific orientation with the point of the triangular mounting plate facing the tow vehicle as with most of…

view full answer...

Answer 10

You can rotate an A-frame jack like the Stomberg Carlson Jack part #JET-3555 that you referenced if needed to allow you to open your rear hatch. The bolt pattern of the jack is allows for mounting of the jack in any orientation.

view full answer...

Answer 11

Yes, you can mount the Ultimate Trailer Jack part #322-RDJ-2K so that the release pin faces outward instead of towards the trailer. All you need to do is rotate the jack until the mounting holes line up and the pin is pointed away from the trailer.…

view full answer...

Answer 12

I spoke with my contact at Lippert and he confirmed that the Lippert Components Power Tongue Jack 1817941 #LC285318 can be rotated to be best orientated for you. The jack can be un-bolted, rotated, and reinstalled.

view full answer...