Will I Need to Drill Holes in my 1999 Ford Super Duty to Install K-Source Towing Mirrors

Question

Question:

Does these mirrors bolt right up to where my current mirrors are without drilling new holes?

asked by: MATT K

0

Expert Reply:

The K Source Custom Towing Mirrors # KS61067-68F that your referenced will utilize the same mounting points as the factory mirrors on your 1999 Ford Super Duty so you would not have to drill any additional holes.

expert reply by: Jameson C

0

Answer 1

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 2

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 5

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 6

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 7

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 8

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...

Answer 9

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Will I Need to Drill Holes in my 1999 Ford Super Duty to Install K-Source Towing Mirrors

Product Page this Question was Asked From

Continue Researching