Installation Instructions for Draw-Tite Class I Receiver # 36336 for 1994 Toyota Camry

Question

Question:

Can you send me or provide on the web installation instructions? I know there was some issue regarding installing under/over/around some part of the exhaust system. I have a 1994 4-door Camry. Thanks.

asked by: Mark

0

Expert Reply:

I linked a copy of the instructions for you along with an installation video on a 2005 Camry for you to check out.

expert reply by: Mike L

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 4

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 8

You'd need to go with the tire part #TT48012C as it's only option for 12 inch wheel that has an 81 mph speed rating and then for a matching wheel part #AM20124 which has the 4 bolt pattern you need. We also don't have a way to mount them…

view full answer...

Answer 9

The Replacement Hinge Pin #362TRCHingePin2 is 0.12" in diameter.

view full answer...

Answer 10

I have reviewed the installation instructions for the Draw-Tite Class II hitch, part number 36336. There is no indication of cutting the fascia or bumper for the 1999 Toyota Camry. The receiver opening sits flush with the rear fascia or bumper cover.…

view full answer...

Answer 11

I attached three links to this page that offer tips in cleaning weld nuts. This will help you install the Draw Tite part #36336 on your 2004 Toyota Camry.

view full answer...

Answer 12

Wow, your boat sitting just 1/2" from your axle is definitely a concern. You should have 4-1/2" of clearance for to keep your boat safe from bumps when traveling. I can understand not wanting to spend the money on a over-under conversion…

view full answer...

Installation Instructions for Draw-Tite Class I Receiver # 36336 for 1994 Toyota Camry

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching