Jack Handle Replacement for Bulldog 8k Square Jack 190574

Question

Question:

190754 bulldog jack bolt on or weld on Looking for jack handle

asked by: Zack G

0

Expert Reply:

The correct replacement handle you need for your Bulldog 190754 which is a 8k square jack is the part # BD500171. I attached an install video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

For your RAM 8000 Series jack #TJD-7000S, you can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks #TJD-7000S-HD for a replacement handle and handle pin. If by pin you were actually referring to the footplate keeper…

view full answer...

Answer 2

You can use taller equalizers but you will likely have to add taller hangers too so that everything increases in height the same. Otherwise you will have a suspension that is not level. I have included a link to the hanger main page for double-eye…

view full answer...

Answer 3

You'll basically just need to remove as much of the oil from your hubs as you can and then pack them with grease instead of oil. Oil seals and caps seal better than grease seals and caps so to make the conversion you want to make is not hard at…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Jack Handle Replacement for Bulldog 8k Square Jack 190574

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching