Air Bags For A Newmar 26,000lb Allegro Motorhome

Question

Question:

I need air bags for a newmar 40ft ford chassis 2016 26000 plds gvw

asked by: Michael L

0

Expert Reply:

I recommend the SumoSprings Rebel Custom Helper Springs # SSF-173-40-2 for front axles and the
SumoSprings Maxim Custom Helper Springs # SSR-187-54-1 for the rear.

Included are video resources with additional information on both including overview and installation steps to review.

expert reply by: Patrick R

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

I have a solution for you but the B&W Companion OEM 5th Wheel Hitch for Chevy/GMC Towing Prep Package item #BWRVK3715 doesn't fit the Chevy trucks before 2020 that don't have the puck system in the bed. The first year of the GM Towing…

view full answer...

Answer 3

Yes it does! The B&W Companion 5th Wheel Hitch #BWRVK3600 that fits your 2018 Ram 2500 with the factory puck system is completely compatible with a MORryde cushioned pin box. This is a fantastic set up, giving you a cushioned pin box along with…

view full answer...

Answer 4

While we don't carry specific fit exterior ladders for RV's we do carry universal options like the Stromberg Carlson RV Exterior Ladder w/ Hinges #LA-401BA, which can be cut down to fit your application. I've attached a video below where…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...