What is Hole Diameter of Ram 5-Position Adjustable Channel Bracket # CTA-CB6

Question

Question:

YOUR SPECS SHOW THE HOLE DIAMETER AS 3/4, SHOULDNT THAT BE 5/8inch LIKE ALL THE OTHER CHANNELS? THANKS

asked by: CRAIG H

1

Helpful Expert Reply:

Yes, the diameter of the holes of the Ram 5-Position Adjustable Channel Bracket for Couplers # CTA-CB6 does have 5/8 inch diameter holes.

I attached a review video that has this dimension and others shown.

expert reply by: Jameson C

1

Answer 1

Although it's intended to be bolted in place, the Demco #DM15349-52 coupler mount could certainly be welded instead. I've linked you to a product description video featuing the #DM15349-52 A-Frame coupler mount.

view full answer...

Answer 2

I spoke to Demco, and unfortunately the Coupler #DM15349-52 cannot be mounted to the bottom of a frame. They went on to say that there would not be enough surface area for it to handle the weight when welded or bolted on. That being said, the Ram…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 6

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 7

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...

Answer 8

The Timbren Silent Ride #TSR14KT01 can actually be installed by welding it on or bolting it on. You could do both welding and bolt it on, but that is not really necessary. I am not sure of the bracket to move it around on the frame, but they do have…

view full answer...

Answer 9

You will need to lock out the sliding function on your Pull Right 5th wheel hitch to use the Ram Gooseneck to 5th Wheel Trailer Coupler Adapter item #KPG5-R30IP. If you can not lock out your slider than I recommend the Curt Spyder Gooseneck Trailer…

view full answer...

Answer 10

The Bulldog Winch Trailer Winch #BDW10039 is 24" long x 7-1/4" wide x 7-1/4" tall so it will have no issues fitting on your recessed plate on your trailer. The winch includes a mounting plate that is 20" long and 7-3/8" wide.…

view full answer...

Answer 11

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...