Diameter of Center Shaft that Holds Handle on Pro Series Round Topwind Jack PS1400300303
Question:
What is the diameter of the shaft protruding from the top of the jack where the crank is attached.
asked by: Michael W
Expert Reply:
I went out and to our warehouse and measured the center shaft on one of our Pro Series Round, Snap-Ring Swivel Jack Topwind # PS1400300303. The shaft is 1/2 inch in diameter.
If you're looking for a replacement handle, the Replacement Handle for Top Wind Style Trailer Jacks # DL22674 will work well as it use the same size (1/4 inch) hardware and is right at about the same length (7 inches). Pro Series does not offer a direct replacement jack handle.
If that's not what you're after, let me know what you're trying to do to see if I can come up with a solution for you.
Products Referenced in This Question
Replacement Handle for Top Wind Style Trailer Jacks by Dutton-Lainson
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Topwind
- Dutton-Lainson
more information >
Product Page this Question was Asked From
Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Shop: Replacement Handle for Top Wind Style Trailer Jacks by Dutton-Lainson
- Shop: Replacement Topwind Handle for etrailer and Ram A-Frame Jacks - 2,000 lbs and 5,000 lbs
- Search Results: trailer jack replacement handle
- Search Results: trailer jack
- Search Results: bushing
- Search Results: handle for trailer jack
- Q&A: Replacement Swivel Trailer Jack for Fulton Pro Series 1,000 lb Jack
- Q&A: Looking for a Bolt-On Jack That is Less Than 11 Inches When Attached
- Shop: Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Shop: Bulldog Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Shop: Replacement Retaining Ring for etrailer and Ram Snap Ring Swivel Jacks
- Shop: Replacement Weld-On L-Bend Bracket for Bulldog and Fulton Snap-Ring Swivel Jacks
- Shop: Wet Equalizer Bolt with Castle Nut, Grease Zerk and Cotter Pin - 3-1/2" Long
- Video: Dutton-Lainson Trailer Jack DL22674 Review
- Video: Review of etrailer Replacement Topwind Handle etrailer Ram A-Frame Jack - TJA-2000-HD
- Article: Trailer Wiring Diagrams
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Search Results: 68149
- Video: Choosing the Right Brake Controller
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Shop: Fifth Wheel Hitch
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: Trailer Tire Sizing