Which Draw Tite Front Hitch Fits 1993 Motorhome Build on Ford E-350 Chassis

Question

Question:

will a 65005 front draw tight hitch work on a1993 ford e350 motor home?

asked by: David

0

Expert Reply:

We have a Draw Tite hitch that fits your 1993 E-350 motorhome chassis but it's the part # 65001 and not the one you mentioned.

I attached an install video for the hitch on a very similar 2007 Ford E-350 motorhome as yours for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite Front-Mount Hitch #65053 is a confirmed fit on the 2008 Ford E350 cutaway chassis. This same front hitch also fits the base E-150, E-250, and E-350 versions. The written instructions and a helpful installation article are linked for…

view full answer...

Answer 2

The E-350 is not the same as the F-350 frame. The E-350 cutaway is the van chassis not the truck chassis. The custom options we have are not a confirmed fit for the cutaway chassis, so you instead will want to use an RV hitch receiver. I recommend…

view full answer...

Answer 3

If the bolt holes are 38-5/8 inches from frame rail to frame rail on your 2008 Ford E350 the Draw Tite Hitch part #75703 will fit your cutaway model. I attached an install video for the hitch for you to check out as well.

view full answer...

Answer 4

If the utility body on your 2006 Ford E-350 van chassis does not sit any lower relative to the frame than on the regular van models you can install a trailer hitch. For example Curt trailer hitch #14055 will work as long as the bolt holes on the…

view full answer...

Answer 5

I read through the instructions for the Draw-Tite hitch, #41546, and while it does mention the E-350 a couple of times, I cross referenced your 2008 Ford E-350 with the Draw-Tite catalog and fit guide I have. This hitch was not recommended for the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Which Draw Tite Front Hitch Fits 1993 Motorhome Build on Ford E-350 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching