Replacement Camper Roof Vent Lid with Continuous Hinge on Dutchmen Kodiak

Question

Question:

I own a 2016 Dutchman Kodiak 201QB. The openingsseat measure 13 x 13 and the outside dimension of the cover is just under 15 square. Smoke color or clear/milk is fine. Want to order the right one. thanks,

asked by: John P

1

Helpful Expert Reply:

Thank you for the pictures!

The correct replacement lid for your roof vent assembly is the Ventline # BV0554-01 in White or # BV0554-03 in Smoke. I think the Smoke version matches your existing unit a bit better but it's completely up to you - both will work great as replacements.

I have attached an installation video that you can also follow along with.

expert reply by: Chris R

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

In order to find the correct replacement parts you will need to measure center hole to center hole on your current shackles. You will also need to measure the inner and outer diameter of your bushings. The Lippert AP Kit - Tandem Axle Road Armor Wet…

view full answer...