Comparing the Curt and Draw-Tite Trailer Hitches for a 2019 Chevrolet Blazer

Question

Question:

We just got a 2019 Chevy Blazer and we need a trailer hitch but I can't decide between the Curt and Draw-Tite. What do you recommend?

asked by: Jim

0

Expert Reply:

The Draw-Tite Class III Max Frame Receiver Hitch part # 76023 and the Curt Class III Receiver Hitch part # C13418 are both excellent options for a 2019 Chevrolet Blazer. I recommend going with the Curt Class III Receiver Hitch because it will be much easier to install than the Draw-Tite Class III Max Frame Receiver Hitch. The Draw-Tite Class III Max Frame Receiver Hitch requires that you remove the rear bumper fascia whereas the Curt Class III Receiver Hitch just requires that you lower the exhaust. The time difference between these two install procedures is around 1:30.

The Draw-Tite Class III Max Frame Receiver Hitch also requires that you trim the rear bumper fascia whereas there is no trimming involved with the Curt Class III Receiver Hitch. They will both fit behind the rear bumper panel once installed and they are both drill free options though as stated the Curt Class III Receiver Hitch is much easier to install.

If you will be towing a trailer then you will also need the Curt T-Connector Vehicle Wiring Harness part # C56325 for a 4-way or the Curt T-Connector Vehicle Wiring Harness part # C56326 for a 7-way. If the trailer has brakes then a brake controller will be needed as well for which I recommend the Curt Echo Mobile Trailer Brake Controller part # C51180.

expert reply by: Conner L

0

click to enlarge

Answer 1

I have two great trailer hitch options for a 2019 Chevrolet Blazer, the Draw-Tite Max-Frame Trailer Hitch Receiver part #76023 and the Curt Trailer Hitch Receiver part #C13418. I recommend the Curt Hitch which is a bit more expensive but also loads…

view full answer...

Answer 2

Yes, for your 2020 Chevy Blazer we have the Curt Class III Trailer Hitch Receiver #C13418, which is a perfect fit and will line right up to existing holes in the frame rails for a simple bolt-on, no-drill installation. It will provide you with a…

view full answer...

Answer 3

I highly recommend the Curt Trailer Hitch #C13418 for your 2020 Chevy Blazer over the Draw Tite part #76023 for two big reasons. The Curt has better towing capacities and is much easier to install! It also looks really great as it fits through the…

view full answer...

Answer 4

Yes, the Curt Hitch - 2" #C13418 will fit a 2021 Chevy Blazer RS. If you need assistance with installing the hitch, I've attached a video to walk you through the process. If you need brake light/turn signal capability when transporting a…

view full answer...

Answer 5

Yes! The Curt Hitch - 2" #C13418 is confirmed to fit your 2022 Chevy Blazer RS. The hitch comes with a simple bolt-on installation and only takes about 40 minutes to complete. Also, since the bottom of the receiver tube measures about 16 inches…

view full answer...

Answer 6

The only difference between the Curt and etrailer trailer hitches that fit your 2023 Chevy Blazer is the finish. The Curt has a glossier finish than the matte black finish of the etrailer hitch, so you can choose which you prefer. The hitches that…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I highly recommend the Curt Trailer Hitch #C13418 for your 2019 Chevy Blazer, and this is the one I would put on mine over the Draw-Tite Trailer Hitch #76023. The reason why I recommend the Curt is because it is far easier to install than the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...