How to Lower Center Jacks on Lippert 3.0 Ground Control System

Question

Question:

Had out of stroke error wanted to reset so lowered front and back jacks 6 inches could not get center jacks to come down at all

asked by: James T

0

Expert Reply:

Pressing the left and right buttons together will activate the middle jacks on the Ground Control 3.0 # LC675817 which is how you'll need to lower them so that you can raise them up and clear the out of stroke error code. Try that and let me know if that helps!

expert reply by: Jameson C

0

Answer 1

Really you're going to need to measure the distance where the leveling system is going to be installed. If that distance is more than 20', then you're going to want the 6 point Lippert Ground Control 3.0 Electric 5th Wheel RV…

view full answer...

Answer 2

I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the #LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam. If…

view full answer...

Answer 3

Yes, you can either use a 3/8" drive ratchet and extension (no socket) at the top of the jack motor (A) or a 3/8" drive ratchet, ratchet extension and 5/16" socket at the bottom of the jack motor (B) to manually raise or lower the…

view full answer...

Answer 4

If you get the Out of Stroke error message on the Lippert Ground Control system, such as #LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further. To clear the error you can extend all of the jacks in…

view full answer...

Answer 5

The "Out of Stroke" error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 4-Point Set #LC358590 and 6-Point Set #LC675817 means that they have reached the max height, can no longer lift so you need to relocate your…

view full answer...

Answer 6

Both the Equa-Flex Cushioned Equalizers - Double Eye Springs like #LC279687 and the E-Z Flex Heavy Duty Rubber Suspension System like the #K71-653-00 will provide an upgrade over the standard cast equalizers that most likely came on your trailer.…

view full answer...

Answer 7

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 8

If you are receiving the ****ERROR**** "Auto Level Fail" LCD Message on for your Lippert Ground Control 3.0 #LC358590 then that means it is either unable to auto level because of uneven ground or it is unable to auto level because the…

view full answer...

Answer 9

Yes you can use the Lippert Solid Stance RV Step Support Kit #LC96BJ. This support kit will work with steps 5" to 14" off the ground, and measures 22-3/4" wide x 2-5/8" tall x 4-1/2" deep when folded. Attached is a review…

view full answer...

Answer 10

I sent your picture to my tech contact at Lippert and they responded with saying that the mounting brackets are designed to go behind and under the cross shaft of the slide out. If you check out the picture I attached you'll see how it would fit…

view full answer...

Answer 11

It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix your issue then please just let me know and I will see if we have any…

view full answer...

Answer 12

On the Lippert Ground Control 3.0 #LC358590 the error you are receiving indicates either a problem at the left front jack, a hall signal issue (open ground/short, or other malfunction) or an unexpected high amperage current stall (meaning the battery…

view full answer...

How to Lower Center Jacks on Lippert 3.0 Ground Control System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching