No Stop/Turn Lights On One Trailer But Other Trailer Works Fine

Question

Question:

I have a 2018 Tacoma P/U. I have two trailers, the jet ski trailer lights work - turn signals, brakes, reverse, running lights. On the utility trailer only the running lights work. The jet ski trailer has a normal connector, 4 pin/4 wires in white, green, brown, yellow. The utility trailer has a 4 pin/5 wire connector, white, green, 2 browns one each side and yellow. Are you familiar with this type of connector? I havent had a chance to check the continuity on the ground and wanted to get your thoughts.

asked by: Jennifer W

0

Expert Reply:

Yes, the utility trailer has what is called a wishbone style 4-way trailer wiring harness and it's actually pretty common.The only difference between this and the standard 4-way trailer wiring harness on your jet ski trailer is that there is a running light wire for each side of the trailer instead of being joined into one wire before being ran up to the trailer connector.

That said, the above difference is not the issue with your stop/turn signal lights. I first recommend you reground the trailer connector but if this does not fix the issue then start tracing the green/yellow wires back while checking for breaks. There could also be an issue with the ground for either tail light. If you want you could just install a new trailer wiring harness, the 35 Ft 4-Way Trailer Wiring Harness part # A35W42B.

expert reply by: Conner L

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

No Stop/Turn Lights On One Trailer But Other Trailer Works Fine

Product Page this Question was Asked From

Continue Researching