Dimensions for Ultra-Fab Electric A-Frame Jack # UF38-944017

Question

Question:

Is there a measurements drawing for this jack like the one provided for the JET-2500 QandA section?

asked by: Dana R

1

Helpful Expert Reply:

I reached out to my contact at Ultra-Fab and he was able to provide me with a detailed dimensional drawing for the Electric A-Frame Jack # UF38-944017, which I have attached below. I have also included a short video review that you can check out as well.

Please just let me know if you need anything else!

expert reply by: Chris R

1

click to enlarge

Answer 1

The Stromberg Carlson #JET-2500 Electric Trailer Jack you referenced has a lift capacity of 2500 lbs. The jack will work just great for trailers with tongue weights less than 2500 lbs, the tongue weight of your Coachmen Cascade should certainly be…

view full answer...

Answer 2

The Ultra-Fab Electric A-Frame Jack #UF38-944017 that you referenced is best installed on your A-frame horse trailer with a separate 12V power source, a secondary battery on the trailer. The tow vehicle 7-way's 12V feed is designed to provide…

view full answer...

Answer 3

From the top of the trailer jack part #UF38-944017 to the bottom of the mounting bracket for the jack measures 18 inches.

view full answer...

Answer 4

From the outside of the jack tube of the #UF38-944017 to the furthest point out on the jack motor housing it measures 3-7/8 inches.

view full answer...

Answer 5

The best option for an economy electric A-frame jack for your 2020 Forest River Salem FSX travel trailer is one from Ultra-Fab: - Ultra-Fab Electric A-Frame Jack #UF38-944017 The Ultra-Fab #UF38-944017 is priced extremely well and is relatively…

view full answer...

Answer 6

The Ultra-Fab Electric A-Frame Jack, part #UF38-944017, requires a 12V power source. You have a couple of options for getting power to the power jack. You can use a quick connect like part #DL24086, and run a wire from the towing vehicle battery,…

view full answer...

Answer 7

The Ultra-Fab Electric A-Frame Jack #UF38-944017 is one of our most economical jacks and has the same 3" on center bolt pattern. This jack is rated for up to 3,500lbs and comes with a 5-year warranty. To install you will simply bolt this jack in…

view full answer...

Answer 8

There is an option for an electric A-frame trailer jack that with an outer tube diameter of 2 inches, though the jack you mentioned has an outer tube diameter of 2-1/4 inches. For an electric A-frame trailer jack that has an outer tube of 2 inches…

view full answer...

Answer 9

Absolutely! From the top of the Stromberg Carlson Electric Trailer Jack #SC63VR to the mounting flange is 21-1/4" and from the front of the jack to the tube is 5-5/8" as shown in the included diagram. I included a video of the #SC63VR for…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Dimensions for Ultra-Fab Electric A-Frame Jack # UF38-944017

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching