Distance from Jack Tube to Outside of Jack Motor on the Ultra Fab Jack UF38-944017

Question

Question:

I am concerned about clearance between the jack head and my propane bottles. Can I have the dimensions of the head of the Ultrafab 3500 in reference to the tube Of the jack? Thanks!

asked by: Chuck D

0

Expert Reply:

From the outside of the jack tube of the # UF38-944017 to the furthest point out on the jack motor housing it measures 3-7/8 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

From the top of the trailer jack part #UF38-944017 to the bottom of the mounting bracket for the jack measures 18 inches.

view full answer...

Answer 2

The Ultra-Fab Electric A-Frame Jack #UF38-944017 that you referenced is best installed on your A-frame horse trailer with a separate 12V power source, a secondary battery on the trailer. The tow vehicle 7-way's 12V feed is designed to provide a…

view full answer...

Answer 3

I reached out to my contact at Ultra-Fab and he was able to provide me with a detailed dimensional drawing for the Electric A-Frame Jack #UF38-944017, which I have attached below. I have also included a short video review that you can check out as…

view full answer...

Answer 4

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 7

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 8

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Distance from Jack Tube to Outside of Jack Motor on the Ultra Fab Jack UF38-944017

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching