Rear Bumper Fit for 2004 Chevy Silverado 2500LD

Question

Question:

Which black diamond plate bumper and hardware kit would I need to order to fit the rear of a 2004 Chevy Silverado 2500 with a Duramax?

asked by: Patrick W

0

Expert Reply:

We do have bumpers that fit your truck, although I checked with Westin and there is not a mounting kit for your 2004 Chevy Silverado 2500 that will allow you to install one of the universal black diamond plate bumpers.

For a similar bumper which is a custom fit if you have an '04 Silverado 2500LD there is the Westin Perfect Match Series Rear Step Bumper - Chrome Plated Steel # 31006.

expert reply by: Kyle S

0

Answer 1

The Westin #66000 is not a fit for your 2004 Chevy Silverado 1500, however we do have a bumper that is confirmed to fit your truck. It is the Westin Perfect Match Series Rear Step Bumper - Chrome Plated Steel #31006.

view full answer...

Answer 2

If your 2002 Chevy Silverado 3500 features the standard factory rear bumper (and not a 10 inch deep drop bumper) then the correct Curt hitch is the Class V #C15312 that you referenced. I have attached an image that shows the difference between a…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #C15312 is what I recommend as a replacement for the factory trailer hitch on a 2002 Chevrolet Silverado 2500HD. In regards to the bolt hole spacing, this will be a different for the Curt Trailer Hitch Receiver as…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Sometimes just use of new spring bars can update a weight distribution hitch to match the tongue weight (TW) of a new trailer, but in the case of your Equal-I-zer system, part #EQ37140ET, the highest-rated bars are the 1400-lb set #EQ90-01-1499 that…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Rear Bumper Fit for 2004 Chevy Silverado 2500LD

Product Page this Question was Asked From

Continue Researching