Where is the Draw-Tite Hitch 75751 for a 2011 Ford Escape Made
Question:
where is 75751 drawtite made?
asked by: Bill H
0
Expert Reply:
The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75751 is made in Mexico. If you are instead looking for a made in USA trailer hitch for your 2011 Ford Escape then you would want the Curt Trailer Hitch Receiver part # 13650. I have attached an install video and photo of the Curt hitch for you. The Curt hitch does have a lower capacity than the Draw-Tite but the vehicle will be your limiting factor to the point where this would not be an issue.
expert reply by:
Conner L
0
click to enlarge
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5250 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Performance Chip Tuners
- Q&A: Differences between the Curt Trailer Hitch # C13651 and # 13650 for a Ford Escape
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Replacement Hardware Kit for Trailer Hitches
- Video: Trailer Hitch Installation - 2006 Ford Escape Hybrid
- Q&A: Exhaust Hanger Touching Hitch and Transferring Vibration and Noise through a 2010 Mercury Mariner
- Shop: Trailer Wiring
- Q&A: Bolt Fishing Wire for the Installation of a Curt Hitch on a 2006 Ford Escape
- Q&A: Do I Have to Drill to Install the Curt Class III Trailer Hitch on a 2009 Ford Escape
- Q&A: Availability of Replacement Hardware for Curt Class III Hitch # 13650 on 2008 Ford Escape
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Search Results: hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: trailer hitch
- Article: My Trailer Hitch Doesn't Fit
- Shop: Brake Controller
- Search Results: trailer hitch wiring
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Search Results: cargo carrier
- Shop: Roof Rack
Explore Expert Info
![Our Expert]()
on Trailer Hitch
on Trailer Hitch
