Can Roof Vent Lid of RV Be Replaced

Question

Question:

Hi my vent cover on my RV is cracked., the kind with the fan. I was wondering can I replace just the cap.. thank you

asked by: Barb M

1

Helpful Expert Reply:

Yes, just the lid of your RV roof vent can be replaced but we have to first determine what roof vent you have now so we can pick out the correct replacement.

The best way to find the correct replacement vent cover for your cargo trailer is to measure the vent. Most standard vents are 14-1/4 by 14-1/4 inches wide, 14 x 14 inches wide or 13 x 14 inches wide. Next if the manufacturer name is on the vent that will help. Finally, you will need to look closely at the hinged portion of the vent.

If there is a rolled metal hinge attached to the vent cover like on the Ventline Replacement Smoke Dome Assembly, part # BV0554-03. Then that is most likely the correct vent for your trailer as long as the measurement matches. There are also vent covers with plastic snap-in style hinges and different raising and lowering arm styles.

Basically the easiest way to select the correct replacement cover is to remove the existing cover and match the hinge and lift bracket to the photos on our site along with the dimensions. A link to all of the replacement vent covers is provided to match up with your cover. # 69284

expert reply by: Jameson C

1

Answer 1

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 3

Hello Brian, we do offer some parts that will work for your application and will be very similar to the BPH1206EPR kit that you mentioned. Like you said, the 12 x 2-1/2 drums are pretty uncommon, so I would have to recommend going instead with the…

view full answer...

Answer 4

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Can Roof Vent Lid of RV Be Replaced

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching