Weight of A-Frame Trailer Coupler # CA-5210-B

Question

Question:

Hi There, Can you tell me how much this coupler weighs?

asked by: Ken D

0

Expert Reply:

The A-Frame Trailer Coupler with Yoke Latch # CA-5210-B weighs just over 7-lbs. The black powder coat finish is great for resisting corrosion and it has an 8000-lb capacity.

expert reply by: Erik B

0

Answer 1

I took a look at your current situation and it's looking like there isn't going to be a replacement latch kit available unfortunately. Instead, you're going to need to replace the entire coupler with something like the A-Frame Trailer…

view full answer...

Answer 2

I went out to the warehouse and measured the coupler part #CA-5210-B and the inside width of the coupler measures 8-3/4 inches. The 9-1/2 inch wide measurement is the outside width of the coupler. If the spot on your tongue where the coupler installs…

view full answer...

Answer 3

Thanks for the photos, and I can confirm that you do have an A-frame style of coupler. We do not have a latch repair kit by that manufacturer for an A-frame coupler for a 2 inch hitch ball, so the best we can offer is a new A-frame coupler. There are…

view full answer...

Answer 4

The etrailer.com coupler, part #CA-5210-B, has a maximum tongue weight capacity of 1,200 pounds. The max towing capacity is 8,000 pounds. That's going to cover the majority of 2 inch hitch balls.

view full answer...

Answer 5

Your trailer should have an identification/safety sticker that indicates its gross vehicle weight rating (GVWR) which is the most the loaded trailer can weigh. If it is a brand new trailer this will unambiguously tell you its capacity; if it was…

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 9

The play you are feeling/hearing is most likely between the hitch ball and the latch of the coupler. If you look under the coupler you can see an adjustment bolt that uses an Allen wrench that will allow you to tighten the latch and get rid of the…

view full answer...

Answer 10

Most A-Frame Trailer Couplers have a standard of 50 degrees. I produced a short video for you showing the angle of the etrailer A-Frame Coupler, part #CA5400. I have also linked an FAQ on trailer couplers.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

It appears TMW is a overseas company which I could not find much information. The 46210 is a common hub number for a 3,500lb idler hub with 5 on 4-1/2" bolt pattern. This would use either the Idler Hub #AKIHUB-545-35-G-K for standard spindles or…

view full answer...