What is Angle of Redline A-Frame Coupler, part # CA5400

Question

Question:

What is the A-Frame angle of this coupler?

asked by: Steve E

0

Expert Reply:

Most A-Frame Trailer Couplers have a standard of 50 degrees. I produced a short video for you showing the angle of the etrailer A-Frame Coupler, part # CA5400.

I have also linked an FAQ on trailer couplers.

expert reply by: Reno H

0

Answer 1

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 2

The best option to replace the hubs on your 1995 Jayco 1207 tent trailer are the Dexter Trailer Idler Hub Assembly item #8-91-05UC1-EZ. This hub has a 4 on 4 bolt pattern and is designed for 2,000 lbs axles with item #L44649 inner and outer…

view full answer...

Answer 3

The Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2-5/16" Ball - 21K #12660-97SP does not have any bolt information, with the reason being that this is a weld-on application and cannot be bolted on. I did cut out…

view full answer...

Answer 4

I can certainly understand how the latch of the Demco 50-Degree A-Frame Trailer Coupler #12660-97SP might seem easily broken, but it's not made from a cheap plastic that would be brittle and easy to break. It's made from a nylon…

view full answer...

Answer 5

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 6

I have another option that may work better for you, but unfortunately we do not have a version of the Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2-5/16" Ball - 12,500 lbs #CA-5296-B for an 18 degree angle frame. The closest…

view full answer...

Answer 7

All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle, is have some steel spacers welded on to get to 50 degrees and then use a weld-on coupler. I have linked the weld-on…

view full answer...

Answer 8

The etrailer Weld-On A-Frame 2-5/16-Inch Coupler, part #CA5400, does not have any adjustment screw to enable you to take up the slack in the fit with your hitch ball. This coupler is produced by a stamping process and this type of manufacturing…

view full answer...

Answer 9

Yes, the Sleeve-Lock A-Frame Trailer Coupler #CA-5196-B that you referenced is a weld-on coupler designed to fit 50 degree A-frame trailers like you mentioned. Nearly all A-frame trailers are 50 degree so it's hard to find A-frame couplers that…

view full answer...

Answer 10

Hydraulic brakes are better suited for boat trailers for the simple fact that wires and water do not like to cooperate with each other, but the etrailer.com Self Adjusting Electric Trailer Brakes, #AKEBRK-35L-SA, can be used on a boat trailer…

view full answer...

Answer 11

There are no repair kits available for the A-Frame Coupler #CA5400, so the best we can offer is to replace it with the same or, if you don't want the oily finish, the A-Frame Trailer Coupler #CA-5400-B.

view full answer...

Answer 12

Unfortunately we don't have a repair kit at this time. If you choose to replace the entire coupler, I recommend the Bulldog Collar-Lok Coupler w/ Low-Profile Latch - 2-5/16" Ball - A-Frame - 12,500 lbs #BD028499. For a bolt on option, you…

view full answer...

What is Angle of Redline A-Frame Coupler, part # CA5400

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching