Replacement Vent Cover for 1998 Winnebago Minnie Winnie RV with Continuous Hinge

Question

Question:

Do you have replacement cover continuous hinge . Inside dimensions141/2×141/2, outside 15×15

asked by: Kim H

0

Expert Reply:

I do have replacement covers available if your roof vent has a continuous hinge. If you are looking for a smoke vent cover then you can use part # BV0554-03 or part # BV0554-01 for a white vent cover. The dimensions you provided are an industry standard size which is classified as 14-1/4" x 14-1/4" so there is no need to get hung up on the 1/4" difference for the inside dimension as these measurements could vary depending on where they are taken from. The covers both measures 15" x 15" outside to outside.

expert reply by: Conner L

0

Answer 1

The vast majority of RV roof vents do measure the common 14 x 14-inch size and fit a roof opening that is slightly larger, 14-1/4 x 14-1/4-inches typically. The item you mentioned, Ventline tinted replacement lid #BVD0449-A03, is for this vent size,…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part #BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would…

view full answer...

Answer 4

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Answer 5

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 6

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 7

I was able to find the OEM part number for the Chevy spare tire hoist but I was unable to find a weight capacity rating on it. The owner's manual for the 2015 Chevy Silverado 1500 and the original hoist can handle the weight of a full sized spare…

view full answer...

Answer 8

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 9

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 10

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 will not have any locking or hold mechanism short of being completely reeled in. I spoke to my tech contact at Lippert who has this on his truck and he said you just crank it up…

view full answer...

Answer 11

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 requires the handle #LC119226 to crank up and down.

view full answer...

Answer 12

To raise and lower the Lippert Spare Tire Winch with Offset Cable #LC159056 what you need is the replacement manual crank handle part #LC119226.

view full answer...

Replacement Vent Cover for 1998 Winnebago Minnie Winnie RV with Continuous Hinge

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching