How to Determine if Kodiak Disc Brake Kit # K2HR35D Will fit Trailer

Question

Question:

I have a 2009 trailer model YMH210G for a YAMAHA SX230. Will this kit work and if so what bearings and seals do I need to go with it?

asked by: Chris W

0

Expert Reply:

I don't ability to look up the trailer axle capacity of your trailer, but if the trailer does have a 3,500 lb axle capacity the Kodiak Disc Brake Kit # K2HR35D would fit and work well. This is a very common axle capacity so it's most likely what you have. You can find this info normally by looking on the axle for a sticker with capacity info or by looking on the plate where the VIN is listed.

The bearings needed are # L68149 and # L44649 and the seal is part # RG06-050.

expert reply by: Jameson C

0

Answer 1

If the inner diameter is 1.719 inches and the outer diameter is 2.565 the #RG06-050 would be the closest matching grease seal we offer. You will need a digital or dial caliper for this measurement. The grease seal number you referenced doesn't…

view full answer...

Answer 2

Based off the measurements you provided, you've got a #84 spindle, so the correct bearings are the #L44649 and #L68149, and #RG06-050 grease seals. We typically try to put bearing numbers of popular manufacturers on the bearing pages but those…

view full answer...

Answer 3

Trailer manufactures rarely make the details of the small parts on their trailers available specifically bearing numbers. I did some research and was not able to find the bearings that fit your ShoreLandr. I am happy to help you replace the bearings…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...