Trouble Locating the Factory Taillight Wiring Harness On a 2016 Lexus NX 200t

Question

Question:

Im trying to run these wires and connect them to the tail lights. I can not find a single wire connecter that fits this trailer wire. I tried googling and looking in the owners manual. No luck. Can you help me locate where to connect this at?

asked by: Shaun

0

Expert Reply:

The T-One Vehicle Wiring Harness part # 118652 is a confirmed fit for your 2016 Lexus NX 200t. This harness actually installs inline with the factory taillight wiring harness so there will not be any sort of unused plug if that was what you were looking for. In order to access the factory taillight wiring harness you need to remove a few trim panels. I have then attached a photo that shows where the factory taillight wiring harness is located.

Unfortunately, we have not yet had the chance to install the T-One Vehicle Wiring Harness on a Lexus NX 200t so I do not have any other advice for you but what might help is to take a look at the install instructions for the Curt T-Connector Vehicle Wiring Harness part # C56268 which I have attached for you as they are more detailed than the ones for the T-One Vehicle Wiring Harness.

expert reply by: Conner L

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...