What Angle Do The Frame Rails Need To Be To Use the Sleeve-Lock A-Frame Trailer Coupler

Question

Question:

Do you have a cad drawing or sketch to show the angle that the frame has to be for this unit to work?

asked by: Chuck

0

Expert Reply:

The Sleeve-Lock A-Frame Trailer Coupler part # CA-5296-B is designed for a standard 50 degree a-frame trailer. If you have an a-frame trailer then this is likely what you have as I would say a good 95% of a-frame trailers use the standard 50 degree angle. I don't have any CAD drawing of the above unfortunately but let me know if you do not have the standard 50 degree angle.

expert reply by: Conner L

0

Answer 1

I would be apprehensive about completely removing the keel rollers, especially if they support any weight. Removing the keel rollers would force the bunks to support more weight. This could be dangerous with the bouncing affect trailers and boats…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

view full answer...

Answer 7

You are correct. Other than how they are made, the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K #DM37ZR and the #DM14793-81 have the same ratings and will work the same. There is no pro or con to either, so…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...