What Gauge Wire Does Hopkins Endurance Easy-Pull 4-Flat # HM47004 Use

Question

Question:

What is the wire gauge used in this product?

asked by: Randy D

0

Expert Reply:

The gauge wire used in the Hopkins Endurance Easy-Pull 4-Flat Extension w/ 2 Grip Rings # HM47004 is 16 gauge.

expert reply by: Jameson C

0

Answer 1

We do have 4-way to 4-way extensions in a few sizes. Like with the part #HM47114 for 48 inches, part #HM47004 for 24 inches or part #HM48144 for 12 inches. We also have 6 foot part #RM-300150-00.

view full answer...

Answer 2

That looks like a standard type of connector that vehicle manufacturers will use for various connections. I couldn't give you a part number for it though. Easiest option would probably be to cut that off and then use the 4-way extension part…

view full answer...

Answer 3

The Hopkins part #HM48235 has 16 gauge for wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264.

view full answer...

Answer 4

It sounds like you are looking for a 4-way flat extension harness. I recommend the Hopkins Endurance Easy-Pull 4-Flat Extension 12" #HM48144. 24" #HM47004, or 48" #HM47114. These extensions will plug into the 4-way flat connector on…

view full answer...

Answer 5

I went out to the warehouse and pulled Hopkins Endurance 4-Way Flat Trailer Connector #HM48110 to measure the wire gauge. The ground wire is 16 gauge and all other wires are 18 gauge. this is adequate for trailer lighting functions since they…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

What Gauge Wire Does Hopkins Endurance Easy-Pull 4-Flat # HM47004 Use

Product Page this Question was Asked From

Continue Researching