What is the Wire Gauge Used in Hopkins Endurance 4-Way Flat Trailer Connector # HM48110

Question

Question:

Can you tell me the wire gauge for these wires? Thanks.

asked by: Jim

0

Expert Reply:

I went out to the warehouse and pulled Hopkins Endurance 4-Way Flat Trailer Connector # HM48110 to measure the wire gauge. The ground wire is 16 gauge and all other wires are 18 gauge. this is adequate for trailer lighting functions since they don't have to carry anything that draws a lot of amperage such as brakes or a 12 volt circuit.

expert reply by: Michael H

0

Answer 1

In your situation I recommend using the Hopkins Endurance 4-Way Flat Trailer Connector part #HM48110. This will replace the 6 round connector on your trailer and allow you to plug it directly into your vehicle. There are no 4-way flat to 6-way…

view full answer...

Answer 2

The Hopkins Plug-In Simple Vehicle Wiring Harness #HM11140244 has been confirmed to currently fit the 2015-2022 Ford Transit T150, T250 and T350 to give you a 4-way flat connector. The Mounting Brackets #18140 and #18144 will allow you to secure it…

view full answer...

Answer 3

The only descriptor that changes the trailer wiring harness needed is whether your 2020 Ford Transit T350 is a SRW or DRW model. If your 2020 Ford Transit T350 has single rear wheels as opposed to duals, the #118643 Tekonsha trailer wiring harness…

view full answer...

Answer 4

Since you have the dually extended version of the 2019 Ford Transit T350 the 4-way wiring kit you'd need is the #118722. We had the chance to install this kit on a Transit like yours which I attached an install video link for on this page. The…

view full answer...

Answer 5

The Ford Transit if equipped with the factory tow package would have came with both a trailer hitch and trailer connector and they would both be located directly under the rear bumper so odds are you do not have either because they are not hard to…

view full answer...

Answer 6

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 7

That looks like a standard type of connector that vehicle manufacturers will use for various connections. I couldn't give you a part number for it though. Easiest option would probably be to cut that off and then use the 4-way extension part…

view full answer...

Answer 8

We do have 4-way to 4-way extensions in a few sizes. Like with the part #HM47114 for 48 inches, part #HM47004 for 24 inches or part #HM48144 for 12 inches. We also have 6 foot part #RM-300150-00.

view full answer...

Answer 9

It sounds like you are looking for a 4-way flat extension harness. I recommend the Hopkins Endurance Easy-Pull 4-Flat Extension 12" #HM48144. 24" #HM47004, or 48" #HM47114. These extensions will plug into the 4-way flat connector on…

view full answer...

Answer 10

The Hopkins part #HM48235 has 16 gauge for wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264.

view full answer...

Answer 11

The gauge wire used in the Hopkins Endurance Easy-Pull 4-Flat Extension w/ 2 Grip Rings #HM47004 is 16 gauge.

view full answer...

Answer 12

The Curt Trailer Connector #C57672 should be grounded to any paint and debris free surface, preferably the vehicle frame; since the hitch is painted, it's not going to provide the best ground source for your 7 way connection. You can extend the…

view full answer...

What is the Wire Gauge Used in Hopkins Endurance 4-Way Flat Trailer Connector # HM48110

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching