Landing Gear Motor Replacement for 1RV-200 on 2005 Pilgrim 276BH 5SS

Question

Question:

Will this motor fit to replace the ADTH 1RV-200 motor on my 2005 Pilgrim 276BH 5SS fifth wheel? I can’t find any specs on the 1RV-200 motor as far as dimensions, Rpms, or weight capacity.

asked by: Paul H

0

Expert Reply:

Your ADTH 1RV-200 landing gear motor that your Ram landing gear uses has a 6,500 lb weight capacity and can be replaced by the # LC142178 that you referenced which has an 8,000 lb weight capacity. The RPM of this is 5,150.

expert reply by: Jameson C

0

Answer 1

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just…

view full answer...

Answer 2

The replacement landing gear for the Keystone Montana will require welding if the brackets need to be replaced. The legs you need are #LC178653 for the lead leg and #LC178652 for the follow leg.

view full answer...

Answer 3

To replace the ADTH 1RV-200 motor on your landing gear the Stromberg Carlson #LG-196308 will work perfectly. This motor is rated for 6,500 pounds like your existing unit. For a gear box replacement you'd want the #LG-179015.

view full answer...

Answer 4

It seems like you have the ADTH 1RV-200 Motor which has a capacity of 6,500 lbs. You can use this replacement motor #LC142178 which has a 4" on center mounting hole spacing. This one is a bit heavier duty than your other which could prevent it…

view full answer...

Answer 5

The 12-Volt Motor Kit #LC142178 referenced in your question is designed for the etrailer.com Landing Gear Set #RVLG-8000, which has a combined weight capacity of 8,000 pounds. This is what the motor is rated for. Based on my research, the Keystone…

view full answer...

Answer 6

The best connector type to use with the 40' 18-Gauge 2-Wire Bonded Wire #SWC77FR are the Deka Heat Shrink Butt Connectors #DW05743-10. You'll insert the ends of the wires into the butt connector, crimp it down, and then use a heat gun or a…

view full answer...

Answer 7

I'm assuming you're wanting to add a brand new unit to your Keystone, in which you're going to want the Advent Air RV Air Conditioner System - Single Zone #ADV64FR. This is exactly what you'll be needing, including a air distribution…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lippert has a wet bolt kit that was specifically designed for use with the Road Armor equalizers with the part #LC52SV. This comes with upgraded heavy duty shackles as well as matching nuts.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To determine if your motorhome has the Tiffin air brake setup or Freightliner BrakeSync you'll need to look at the rear and see if there's an quick disconnect fitting for your air line. The standard Tiffin air coupler fitting would look like…

view full answer...

Landing Gear Motor Replacement for 1RV-200 on 2005 Pilgrim 276BH 5SS

Product Page this Question was Asked From

Continue Researching