Replacement Roof Vent Lid for 2005 Shadow Master Trailer

Question

Question:

Hi, I’m looking for a replacement top for a 2005 Shadow Master trailer, see attached picture

asked by: Simon R

0

Expert Reply:

Thanks for the picture of your roof vent assembly! Based on that I can tell that the replacement vent lid you are looking for is the part # BV0554-03.

I attached an install video for this for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Vent Cover for Ventline Old-Style Rounded Dome Trailer Roof Vents - Smoke part #BV0554-03 is designed to fit the very common Ventadomes and post-1995 Elixir trailer roof vent. If you have one of these models this will be your replacement. If you…

view full answer...

Answer 2

To replace the Ventline roof vent lid you have with the part #BV0554-03 does require removing the interior garnish of the vent so that you can drop the screen and disassemble the operator assembly like what is show in the attached install video.…

view full answer...

Answer 3

We offer two replacement covers for the Ventline AS-13-M-V101. We have a white cover #BV0554-01 and a smoked color #BV0554-03.

view full answer...

Answer 4

Sounds like you are looking for a replacement vent lid for your trailer. Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. The best way to find the correct replacement vent cover for…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...