Replacement Roof Vent Cover

Question

Question:

I am looking for a replacement vent lid. Made Ventline AS-13M replacement No.VB0568.

asked by: Thomas

0

Expert Reply:

We offer two replacement covers for the Ventline AS-13-M-V101. We have a white cover # BV0554-01 and a smoked color # BV0554-03.

expert reply by: Jacob H

0

Answer 1

The Vent Cover for Ventline Old-Style Rounded Dome Trailer Roof Vents - Smoke part #BV0554-03 is designed to fit the very common Ventadomes and post-1995 Elixir trailer roof vent. If you have one of these models this will be your replacement. If you…

view full answer...

Answer 2

Thanks for the picture of your roof vent assembly! Based on that I can tell that the replacement vent lid you are looking for is the part #BV0554-03. I attached an install video for this for you to check out as well.

view full answer...

Answer 3

To replace the Ventline roof vent lid you have with the part #BV0554-03 does require removing the interior garnish of the vent so that you can drop the screen and disassemble the operator assembly like what is show in the attached install video.…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Replacement Roof Vent Cover

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching