Curt Trailer Hitch For 2019 Ford F-550 Cab and Chassis

Question

Question:

Will this hitch fit a 2019 Ford F-550 Cab and Chassis truck?

asked by: Brian F

0

Expert Reply:

Yes, The Curt Class V Trailer Hitch Receiver part # C15845 will fit all models of the 2019 Ford F-550 Cab and Chassis with 34" wide frames outside to outside.

expert reply by: Heather A

0

Answer 1

I would be happy to help! The Curt Trailer Hitch Receiver #C15845 you were looking at is designed to fit the 2003 Ford F-350/450/550 Cab and Chassis motorhomes, and will not work on your 2003 Thor Four Winds Hurricane built on the Ford F53 chassis.…

view full answer...

Answer 2

The Roadmaster Htich Extender #RM-071-1075 measures approximately 3 inches deep from the pin hole to the furthest point inside the receiver tube. It's also only designed to be used to flat tow a vehicle with a hitch style tow bar. It can't be…

view full answer...

Answer 3

You can use hitch extender #RM-071-1075 for things other than flat towing a vehicle. It will fit any 2 inch trailer hitch receiver. However, the tongue weight capacity of the trailer hitch will be reduced by 50 percent when using an extender.…

view full answer...

Answer 4

We do have a large selection of hitch extenders that will allow for the needed clearance between your tailgate and jack. The shortest extender we have available for 2 inch receivers that has the required capacity for your 8,000 pound trailer is the…

view full answer...

Answer 5

The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2-1/2" Hitch #325-GH-1625 weighs a total of 70 pounds. This is because the hitch is made out of heavy-duty steel and is built for brute strength. If you are looking at doing some…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver part #C15845 that you referenced is a confirmed fit for a 2016 Ford F-550 cab and chassis with frame rails spaced 34" apart (outside to outside). However, Curt does not test this trailer hitch with dump body…

view full answer...

Answer 7

Curt 2-1/2-inch Class V hitch #C15845 will fit the 1999 Ford F-450 cab and chassis so long as the frame width (measured outside to outside) is 34-inches. Drilling is required for installation. I went to our warehouse and measured the side-to-side…

view full answer...

Answer 8

The mounting flanges of the Curt hitch part #C15800 are 11.6 inches in length. This is a fit for your 2022 Chevy Silverado 2500 cab and chassis model.

view full answer...

Answer 9

The mounting holes are 16-1/4 inches apart on the Curt hitch, part #C15845. Also the rivet holes are 3 inches apart. I've included the diagrams of all the mounting hole measurements for you. As well as the install details of the hitch.

view full answer...

Answer 10

Please refer to the included images I made showing measurements for Curt trailer hitch #C14048. This hitch is designed to fit 1999 to 2016 Ford cab and chassis model trucks. Those are the trucks sold without a bed and are then turned into service…

view full answer...

Answer 11

Thanks for the photo, that was a big help. And the answer is yes, your 2023 Ford F-350 Cab & Chassis is 100 percent compatible with the Curt 7-way: - Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR…

view full answer...

Answer 12

I do see the Curt Trailer Hitch Receiver #C15845 has been confirmed by Curt to fit your 2024 Ford F-550 Cab and Chassis with a 34" wide frame. For the wiring we do have the Curt T-Connector Vehicle Wiring Harness #C69CR which Curt has also…

view full answer...

Curt Trailer Hitch For 2019 Ford F-550 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching