Dimensions of Curt Trailer Hitch C14048 for Ford Cab and Chassis Trucks

Question

Question:

What is the distance from the side plate to top of cross tube? Distance between mounting holes on the side plate? Height of the side plate front and rear?

asked by: Mike

0

Expert Reply:

Please refer to the included images I made showing measurements for Curt trailer hitch # C14048. This hitch is designed to fit 1999 to 2016 Ford cab and chassis model trucks. Those are the trucks sold without a bed and are then turned into service vehicles, flat beds, and utility trucks.

expert reply by: Michael H

0

click to enlarge

Answer 1

The 2017 GMC Sierra 3500 cab-and-chassis is a confirmed fit for the Draw-Tite Ultra Frame Trailer Hitch #41947 so long as the truck frame width dimension is 34-inches from outside edge to outside edge. This frame dimension requirement applies to all…

view full answer...

Answer 2

The mounting holes the Curt Trailer Hitch Receiver #14053 measure 38-1/4" (for the 4 rearmost) and 38-3/4" (for the 1 forward-most) and then from the edge of the receiver that measurement is either 4-1/2" or 17-3/4" depending on…

view full answer...

Answer 3

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 4

Yes, we do. I have attached them below. This hitch is confirmed to fit the 1985 Chevrolet C/K Series Pickup with the 6' or 8' beds with a standard or step bumper and the cab and chassis models.

view full answer...

Answer 5

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 6

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 7

I went out into our warehouse to measure the mounting flange of the Curt Hitch part #14053 that you referenced and found it to be 15-1/8 inches long.

view full answer...

Answer 8

The Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center - Custom Fit - Class V - 2" #41946 is a confirmed fit for your 2005 Chevy Express van but the measurements are correct. This hitch does require drilling to install rounding out the…

view full answer...

Answer 9

The Curt Trailer Hitch Receiver part #C15845 that you referenced is a confirmed fit for a 2016 Ford F-550 cab and chassis with frame rails spaced 34" apart (outside to outside). However, Curt does not test this trailer hitch with dump body…

view full answer...

Answer 10

I believe the 2022 Ford F-450 Super Duty has 19.5" wheels, verify this for your vehicle. I suggest the Wheel Masters 4-Hose Inflation Kit, #WM8001 which is for wheels up to 19.5".

view full answer...

Answer 11

Thank you for the excellent photos, and for starters, you are correct that it will help ease installation if you lower the gas tank on your 2005 Ford F-350 Cab and Chassis when installing the Curt Trailer Hitch Receiver #C14048. In regards to…

view full answer...

Answer 12

In regards to the Curt Trailer Hitch Receiver part #C14048, the distance from the center of the front mounting hole to the center of the rear mounting hole is 17-1/4". The distance from the center of the mounting holes left to right is 31".…

view full answer...

Dimensions of Curt Trailer Hitch C14048 for Ford Cab and Chassis Trucks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching