Where Does Brake Controller Install on 2019 Fleetwood Flair 35R

Question

Question:

Where is the Electric brake connector plug on a 2019 Fleetwood Flair 35R. F-53

asked by: Dennis B

1

Helpful Expert Reply:

The Plug-In Adapter # 3035-P the correct harness to install the Tekonsha Brake Controller # TK90160 on your 2019 Fleetwood Flair 35R RV that's built on the 2018 Ford F-53 chassis.

This factory port on the F-53 is located on the left hand side of the steering column support near the emergency brake pedal. I have attached a picture that shows where to find it as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...