Availability of a Trailer Hitch Ball with a 1-1/4 Inch Shank and a 1-7/8 Inch Diameter

Question

Question:

i have 2 smaller trailers that require a 1-7/8 ball, is there a heavy duty ball that size that will fit this mount. thank you

asked by: Rick

0

Expert Reply:

The only 1-7/8 inch ball that we carry with a 1-1/4 inch shank is # C48810, but this is used for a pintle hitch combo hitch. What you can do is use a bushing like # F-2 to go from a 1-1/4 inch ball hole to a 1 inch. You could then use a ball like # 19260.

expert reply by: Michael H

0

Answer 1

The Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount part #CAB-UM is indeed an excellent option that will help improve the overall towing experience by decreasing the felt road shock in the tow vehicle. The Convert-A-Ball in particular as you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 8

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...