Does Motor for Raising and Lowering Lid of Ventline Ventadome part # V2119-3-533 Power In and Out

Question

Question:

Is the cover motor 2 position, or a spring returning type?

asked by: Jeremy

1

Helpful Expert Reply:

The motor that raises and lowers the lid of the Ventline Ventadome part # V2119-3-533 that you referenced powers in and out to raise and lower it.

expert reply by: Jameson C

1

click to enlarge

Answer 1

If your current vent has a rough opening size of 14-1/4 square inches then the Ventline vent, #V2119-601-00, is the best option for you. The fan and opening mechanism are powered and can be activated with a wall switch, #VC0533-03-A. To install the…

view full answer...

Answer 2

The model Fan-Tastic fan you have with the wall mount is discontinued so the only option is to replace the fan and remove the wall mounted thermostats. You can replace the vents with the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote #FV807350 which…

view full answer...

Answer 3

To connect the Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent #MA59FR you will need - if you don't have it - the Replacement Control Cable for MaxxAir MaxxFan Plus Roof Vent Wall Control Panel #MA69FR. You'll need to route that cable…

view full answer...

Answer 4

You can utilize a power wall remote switch #VC0533-03-A or #VC0533-02-A (black or white). A rocker switch #BL0108-00 will work and you will need 2 of them. The installation kit #344270KITW will come with screws, tape, and sealant. You will also need…

view full answer...

Answer 5

So we can definitely get you a more powerful trailer roof vent than the Ventline Ventadome Roof Vent #V2119-1-533, though the only issue is there isn't one that will be able to utilize your current wall switch, so what you'll need is a vent…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

The number ( 411 D) you provided doesn't correspond with a Fan-Tastic Vent roof vent model number, but if yours uses the remote control #FV9068-09 that you referenced, that tells us it's a 7350 Series Fan-Tastic Vent Roof Vent, like…

view full answer...