Where Should the Breakaway Cable and Pin Be Attached on 5th Wheel Hitch Application?

Question

Question:

Where do you hook your emergency brake cable?

asked by: Steve

0

Expert Reply:

There is not a designated location on a 5th wheel hitch like # RP30144 for the emergency Breakaway Kit # 20099 cable. Most people will connect that cable to the tethered pin that locks the jaws of the head in place near the handle. You can see this at the 5:38 mark on the attached video and I've attached a photo to help as well. This location allows for the hitch to slide as needed without adding any extra tension to that pin reducing the chance of binding and coming disconnected when there isn't a connection issue with the trailer itself.

expert reply by: Jason S

0

click to enlarge

Answer 1

There are many options for attaching the breakaway cable from the Tow Ready Trailer Break Away Kit, item #50-85-315, to your vehicle. You could attach to a tie down point in the bed of your truck or you could use stake pocket tie down and attach…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 6

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 7

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...