Front and Rear Suspension Kits for 2008 Nissan Titan 4 x 4 with WD Hitch and Iron Bull Front Bumper

Question

Question:

I am towing a 30’ 7k pounder trailer with an equal-izer hitch system Is it okay to use the two systems mentioned above, in subject together in the rear, or just go with the leaf helpers. Also I’d like to beef up the front suspension for use with my front hitch system within an iron bull bumper, for positioning the trailer in my back yard area. Could the front air springs system aid and protect in this situation as well... The wt at the hitch is about 650 + the winch and bumper around 300 lbs or is this a bad idea? Thank you for your input and suggestions.

asked by: John M

1

Helpful Expert Reply:

You have an interesting combination of circumstances with your 2008 Nissan Titan 4x4 that is both towing a 7000-lb trailer with a weight distribution hitch (WDH) and also using a fairly heavy Iron Bull front bumper with winch/hitch to maneuver the trailer.

In general, you can say that a WDH and a front-axle suspension helper system will tend to work against each other. The WDH will try to push some of the trailer's tongue weight (TW) forward onto the front axle while the front axle suspension helper spring will try to resist that.

What makes the most sense is to use air springs in the rear, the Firestone kit # F2355 that you referenced is perfect, and jounce spring kit # TFXF1004A in the front which will only engage the axle when it is under the load of the trailer's tongue weight. When towing with the WDH the jounce springs will not interfere with the system as it levels the truck. The air springs will give you more capacity than the leaf spring kit # RAS4611 plus that benefit of instant adjustability.

The air springs' pressure will be far easier to optimize for towing if you use a compressor # F2158 that will allow you to adjust pressure from the driver's seat as you go down the road. You'll want to adjust the WDH or best leveling before you air up the rear axle air bags.

expert reply by: Adam R

1

Answer 1

Between the 1,500 lb SumoSprings #SS95GR and 1,000 lb SumoSprings #SS35GR that fit your 2023 Nissan Titan, the best option is the latter, the 1k springs: - SumoSprings Solo Custom Helper Springs #SS35GR The 1,000 lb capacity is more than enough…

view full answer...

Answer 2

The SumoSprings Solo Custom Helper Springs - Rear Axle, #SSR-117-47, are sold as a pair. It is suspension enhancement for the rear axle on both sides of your truck. These springs are a great upgrade to your factory suspension for improved control and…

view full answer...

Answer 3

The Timbren Suspension Enhancement System #TNRTTNB is designed to only fit a stock suspension height on your 2021 Nissan Titan. You can use the Timbren 1" Spacer #A25723-90AH00 to space out the Timbren for the Rough Country lift since they use…

view full answer...

Answer 4

The height of the SumoSrpings Solo Custom Helper Springs #SS95GR is 5-1/2 inches without the top bolt and 6-1/2 inches with the top bolt. I went ahead and attached a diagram of these dimensions to give you perspective. If you need the confirmation…

view full answer...

Answer 5

The Timbren Front Suspension Enhancement System like part #TFXF1004A should be in constant contact with the front end. If you have a gap from your leveling kit then you will want to use the Timbren 1/2" Spacer for Raised Frame Vehicles part…

view full answer...

Answer 6

For your 2018 Toyota Tundra the suspension enhancement I recommend is the Timbren kit part #TABSOSR because this kit installs easily, gives you the suspension support you need to greatly reduce the sag, and because it doesn't require monitoring…

view full answer...

Answer 7

One end of the umbilical cord that comes with the Brake Buddy Stealth Supplemental Braking System part #HM39530 is a 7-blade round connection that connects to motor home's 7-way plug. The other end is a 7-flat connector that plugs into the…

view full answer...

Answer 8

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 9

Drilling is not required to install Firestone Ride-Ride spring, #F2355, on your 2005 Nissan Titan. Really the most difficult part is routing and cutting the lines. You have to make sure the lines will not be pinched or burned by hot components like…

view full answer...

Answer 10

There are a number of reasons why the brakes on your trailer may not be working. Lets start with the easiest things to check. First, check the vehicle and trailer connectors for corrosion. This can cause a short inside the connector and the brake…

view full answer...

Answer 11

You'll want to use a gear oil for the Trailer Hub and Drum Assembly #8-219-20 that you referenced. 90 weight or 80w-90 would work well.

view full answer...

Answer 12

Dexter recommends a SAE 90, SAE 80W-90 or SAE 75W-90 oil to be used. I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE as it is a synthetic 90 weight oil that helps reduce friction and to keep bearings cool. Since your cap was…

view full answer...

Front and Rear Suspension Kits for 2008 Nissan Titan 4 x 4 with WD Hitch and Iron Bull Front Bumper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching