Are the Spacers Required on the Timbren Front Suspension Enhancement if I Have a Leveling Kit

Question

Question:

Im getting a 2 inch level lift kit for my truck. Trying to figure out if I need additional spacers for the front.

asked by: Russell S

0

Expert Reply:

The Timbren Front Suspension Enhancement System like part # TFXF1004A should be in constant contact with the front end. If you have a gap from your leveling kit then you will want to use the Timbren 1/2" Spacer for Raised Frame Vehicles
part # TA25722-90P00 that you asked about. It is likely you will need them or the larger Timbren 1" Spacer For Raised Vehicles part # A25723-90AH00 to make up the difference.

expert reply by: Randy B

0

Answer 1

You have an interesting combination of circumstances with your 2008 Nissan Titan 4x4 that is both towing a 7000-lb trailer with a weight distribution hitch (WDH) and also using a fairly heavy Iron Bull front bumper with winch/hitch to maneuver the…

view full answer...

Answer 2

When it comes to installing a front suspension enhancement system on your 2016 Nissan Titan XD The Timbren Front Suspension Enhancement System #TFXF1004A will work with your 2WD vehicle. The Timbren system has no drilling required and has a 4,000…

view full answer...

Answer 3

For the body roll the best solution for the rear suspension will be the part #SSA23 as it is designed specifically for fighting body roll and providing rear suspension support. The Timbrens would be the way to go for the front suspension. I would go…

view full answer...

Answer 4

With Timbrens you want to use a spacer to match as close to the amount of lift you have on the truck if the lift raised the frame of your truck away from the axle of the truck. Since you have a 1.5 inch lift you'd want the 1/2 inch spacer part…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

From what I can find on the 2022 Nissan Frontier, the plug for the brake controller that will let you use a harness like the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers #3050-P is located just above the OBD connector, taped tight…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...