Replacement Spring for Fulton T1300 Trailer Winch Made In 1999

Question

Question:

Made in 1999 Is there a spring available for a fulton 1300 winch spring

asked by: Geoffrey L

0

Expert Reply:

I do have an option for you but the spring is no longer available for you Fulton T1300 Trailer Winch made in 1999. Therefore, you will need to replace the entire winch for which I recommend the Fulton Single Speed Winch part # F142104. This winch is a single speed and has a 1,300 lb weight capacity. It can be used with a 20' long x 2" wide strap like part # FWS20HD0200.

expert reply by: Conner L

0

Answer 1

I spoke with my contact at Fulton regarding the Ratchet Repair Kit #F501133 referenced in your question for your T3205 Fulton Winch. He stated that this is an older, discontinued winch, but he was able to verify that the ratchet itself in the kit,…

view full answer...

Answer 2

The first and easiest thing you should check is that the trailer is being towed level. If the trailer is nose high or low that can cause the equalizers to not sit level. You will need to select the correct rise/drop ball mount so that the trailer…

view full answer...

Answer 3

There are a few things I would recommend checking before you start swapping parts. First will be to check the weight distribution with the boat on the trailer. Typically when the rear is hitting the frame like you have the weight may be to much on…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Replacement Spring for Fulton T1300 Trailer Winch Made In 1999

Products Referenced in This Question

Continue Researching