Troubleshooting Trailer Axle Equalizer that Touches Trailer Frame
Question:
the equalizer is touching the bottom of the trailer what is makeing that happen
asked by: Mel R
Expert Reply:
The first and easiest thing you should check is that the trailer is being towed level. If the trailer is nose high or low that can cause the equalizers to not sit level. You will need to select the correct rise/drop ball mount so that the trailer sits level. I attached an FAQ on how to do this.
If there is significantly more weight on one of the trailer axles you will need to adjust the cargo in the boat or the way the boat is loaded on the trailer to get the proper amount of tongue weight and even out the load over the trailer axles. You will most likely find that the weight of the boat is centered too far forward and that moving cargo or positioning the boat slightly rearward on the trailer will increase the clearance for the front side of your equalizers. Be careful not to reduce the tongue weight of the trailer too much or trailer sway can result.
It could also mean that the bushings for the equalizers are worn and will need to be replaced (though it is often easier and more cost effective to just change the equalizers). It is also possible that the wrong size springs were installed on the boat trailer or that they are worn and need to be replaced.
Another thing to check are the shackles. If one is flipped in the wrong direction, you will need to jack up the trailer and return the shackle to the correct position.
If the trailer is not the correct one for the boat, it could cause the problem. If you determine that none of these are causing the problem or are just unsure, I recommend taking the trailer to a qualified trailer mechanic for further troubleshooting.
I have included a link to an FAQ on trailer suspension below. There is a section on equalizers about a quarter of the way down the page. When replacing equalizers, there are several measurements that should be considered. These are outlined in the FAQ article.
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Continue Researching
- Article: Double-Eye Trailer Suspension System Review
- Search Results: shackle links trailer leaf spring suspension
- Q&A: Does Changing From A 4 Leaf To A 6 Leaf Spring Add To Ride Height?
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Q&A: Breaking In Replacement 6,000 lbs Leaf Springs
- Shop: 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long
- Q&A: Proper Position of Equalizer and Shackles on Trailer Suspension
- Shop: 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 26" Long
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs
- Q&A: How Are Shackle Straps Supposed to Be Positioned When The Trailer Is Loaded?
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 3-1/4" Tall - 9/16" Bolt Hole
- Shop: Curved Equalizer for 1-3/4" Double Eye Spring - 7-3/4" Long - 9/16" Hole
- Article: How to Accurately Measure Trailer Leaf Springs
- Shop: BOLT brand vehicle and hitch locks
- Shop: RV Camera
- Q&A: Closest to 2-3/4 Inch Heavy-Duty Shackle Strap
- Article: How to Raise Your Travel Trailer Height
- Article: Slipper Spring Trailer Suspension System Review
- Q&A: What Happens if I Change the Size of Equalizers on 5th Wheel Camping Trailer
- Video: Review of Dexter Axle Trailer Leaf Spring Suspension - Replacement Shackle Link - DX55FR
- Search Results: wire clips
- Search Results: lock
- Search Results: shackle bushing
- Search Results: eq~310
- Video: Spectro Wiring - Tools for Wiring - SWC9024-1 Review
- Video: BOLT Covered Padlock Review BL7018517
- Video: Spectro Wiring Steel Tubing Clamp Review
- Video: TruRyde Trailer Suspension TRSL200 Review
- Video: Dexter E-Z Flex Suspension Kit Review and Installation
Luke S.
7/21/2020
We have the same problem but all of these things have been checked. We did find the the middle axle of three axles is taller than the others. Is that common or even acceptable, or would that most likely be the cause of our equalizer hitting the bottom of the frame?