Can I Access the Switch If I Use Double Sided Tape To Install the ATAK Solar Motion Light

Question

Question:

How on earth could I get to the switch and battery compartment of the ATAK Solar Motion Light - Weatherproof - 900 Lumens if I attach it with the 3M double sticky tape?

asked by: Dietlind S

1

Helpful Expert Reply:

The ATAK Solar Motion Light part # PT702 as the title states is a motion powered light. It is not really designed to be continually turned off and on. The switch on the back is for light intensity so once you find out which intensity is best for you, you can mount the light with either the screws or double sided tape. It would then provide 30 seconds of illumination when movement is detected.

expert reply by: Conner L

1

Answer 1

You are going to want to trim the block down about an inch. We have seen this issue before on similar GMC trucks and if you don't trim the block down the suspension is going to feel incredibly rough. If you trim about an inch off and match the…

view full answer...

Answer 2

Those are good questions, and the SuperSprings Custom Suspension Stabilizer and Sway Control Kit #SSA25 will not replace the factory springs on your 2019 Ford F-450, they work in tandem along with your springs, which will not be removed. These are…

view full answer...

Answer 3

I have a couple of suggestions for you but you are really doing good on your kit so far. The TorkLift SuperHitch Magnum Trailer Hitch Receiver part #TLD1111-30 is what you want for the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear part…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can I Access the Switch If I Use Double Sided Tape To Install the ATAK Solar Motion Light

Product Page this Question was Asked From

Continue Researching