How to Pick Out Replacement Velcro for Access Tonneau

Question

Question:

Can you tell me which Velcro I need? Have a 2003 F350 with 8’ bed has old Access Limited roll up tonneu cover. The Velcro in the bed rails need replaced. Thanks

asked by: Dan J

1

Helpful Expert Reply:

I'm going to need you to measure the width of the Velcro strip of your Access tonneau cover. If the width his 1-1/2 inch you'd need the part # A30474, if it's 1 inch you'd want the part # A60270, or 1-1/4 inch part # A20790.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 6

I pulled the Replacement Velcro Strip, part #A30474 from the warehouse and opened the package to see how it is attached. This is designed to replace the hook side of the velcro fastener on Tonneau covers. Per the instructions you would drill out the…

view full answer...

Answer 7

We do have our Trailer Hitch Receiver Reducer Sleeves #e33YR which includes a 3" to 2-1/2" reducer and 2-1/2" to 2" reducer. These can be used individually or together if you need to go from a 3" to 2" receiver. We do…

view full answer...

Answer 8

I have an answer for you. Unfortunately, we do not carry Gator-brand tonneau covers, so we will not be able to confirm for sure if our replacement replacement Access Velcro strips will fit your tonneau. However, judging by your attached picture and…

view full answer...

Answer 9

The only difference between the Access Replacement Velcro Strips #A30474 and #A60270 is that A30474 is 1-1/2 inches wide and A60270 is only 1 inch wide. They are both 17 feet long and come with the 4 screws to help keep them in place.

view full answer...

Answer 10

You can use the Replacement Truxedo Shur-Bond Velcro Brand Fastener for 8' Beds - 1" Width #TX1117877 which is the width you need and can be cut to length. It doesn't have the adhesive back but rather fits in the groove of the rail.

view full answer...

Answer 11

Although we do not carry Lund tonneau covers or their replacement parts we do have velcro strips that are 1-1/2" wide in the Replacement Velcro Strip part #A30474. The velcro is 17" long which should be more than enough for your 2009 Toyota…

view full answer...

Answer 12

We have replacement tonneau cover Velcro that is exactly 1-5/16 inches wide with the Truxedo part #TX1115174 which would fit your rails. It can be cut down shorter too as it is 80 inches long.

view full answer...