Mounting Bracket Recommendation to Attach Fulton Jack # F500349 to Trailer

Question

Question:

I purchased a Fulton F141132 for my boat trailer, but didnt pay attention to how it was supposed to mount. The Shelby jack I am replacing was attached to a mounting plate that bolted directly to the trailer. The mounting plate center does not work with the Fulton jack. Can you please recommend a mounting plate that will fit a bolt pattern of 5 1/2inch horizontal and 3inch vertical? Thank you very much!

asked by: Gerald P

0

Expert Reply:

The correct mount for use with the Fulton jack # F500349 that you referenced is the part # P9012-00. You'd need to remove the bracket you have on your trailer and have this one welded in it's place.

expert reply by: Jameson C

0

Answer 1

It sounds like you're needing a jack like the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which installs on trailers that already have the mount welded on with a single bolt attachment for the jack itself (like what we see with part…

view full answer...

Answer 2

To replace your Shelby 5856A jack I recommend the Fulton Round Snap-Ring Swivel Marine Jack #FTJ120W0301. We have had customers say that this fits the mounting plate for the Shelby 5784A perfectly so ti's going to be the easiest install possible.…

view full answer...

Answer 3

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 4

Thank you for that info, and while we have some options for you to replace your Shelby 5764A trailer jack, there isn't one that is going to fit that bolt pattern. So you have a couple of things you can do, which is either have a new plate welded…

view full answer...

Answer 5

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

As it seems you already know, when installing a trailer brake controller on your 2007 GMC Yukon you will need to locate the two wires under the hood that need to be connected to fully activate the vehicle's tow package. One is the power wire to…

view full answer...

Answer 10

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 11

Having the extra amperage of the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K has no down side. You'd at worst just have more power available than you'd need.

view full answer...

Mounting Bracket Recommendation to Attach Fulton Jack # F500349 to Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching