Is There Down Side to Progressive Dynamics 4000 Series 60 Amp Over 45 Amp

Question

Question:

Are there any CONS to choosing a 60 AMP 4000 Series Inteli-Power Mighty Mini RV Converter over a 45 AMP? I am replacing an older 25 AMP unit altogether.

asked by: Michael P

0

Expert Reply:

Having the extra amperage of the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp # PD4060K has no down side. You'd at worst just have more power available than you'd need.

expert reply by: Jameson C

0

Answer 1

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 2

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 5

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 6

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 7

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 8

You do not want to use a holding tank heater like ThermaHeat #277-000164 on a battery but we do offer battery heaters specifically intended to protect one from extreme cold. You can see all such items on the page I linked for you. You'll want to…

view full answer...

Answer 9

From the looks of the photo you sent it does not look like you have an OEM suspension system on your boat trailer. I recommend securing the suspension rail to the trailer frame in a more secure manner like drilling and using bolts so that it does not…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 12

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Is There Down Side to Progressive Dynamics 4000 Series 60 Amp Over 45 Amp

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching