Replacement for Shelby Industries Model 5756 Boat jack
Question:
Do you have a direct replacement for this jack? Shelby Industries Model 5756 Boat jack Can I use the currently welded on ring? How do I remove the existing jack and install the new one?
asked by: Todd B
Expert Reply:
According to our research the Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on.
You basically need to open up and remove the clamp that secures your Shelby jack to the bracket. If you check out the attached review video you can see the installation at about the 3:08 minute mark. Just do the opposite of this to remove your jack.
Product Page this Question was Asked From
Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs
- Trailer Jack
- Boat Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- Swivel Jack
- 10 Inch Lift
- Weld-On
- With Wheel
- Fulton
more information >
Continue Researching
- Shop: Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs
- Shop: Fulton Bolt-Thru Swivel Boat Trailer Jack w 2 Wheels - Bolt On - Sidewind - 12" Lift - 1.5K
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
- Shop: Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs
- Video: Fulton Round Snap Ring Swivel Marine Jack Review
- Video: Review of Fulton Trailer Jack - Side Frame Mount Jack - FTJ120W0301
- Search Results: snap ring jack
- Search Results: boat jack
- Shop: CE Smith Carpeted Bunk Boards for Boat Trailers - 6' Long - 1 Pair
- Search Results: snap ring trailer jack
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Bolt On - Sidewind - 12" Lift - 1,500 lbs
- Shop: Pull Pin, Easy Swivel Trailer Jack with 6" Dual Wheels - Sidewind - 1,500 lbs.
- Q&A: Replacement Jack to Fit Mount of Shelby Industries 5756a
- Q&A: Trailer Jack Replacement for Shelby 5862A
- Q&A: 10 Foot Long Carpeted Bunk Boards for Boat Trailer
- Shop: Fifth Wheel Hitch
- Search Results: trailer jack
- Search Results: boat trailer jack
- Q&A: Replacement for Shelby # 5756 1200 lb Jack
- Search Results: trailer d ring
- Search Results: trailer stake pocket
- Q&A: Could Fulton Snap Ring Swivel Jack Replace Shelby Jack
- Shop: Suspension Enhancement
- Video: Ultra-Fab Products Trailer Jack UF49-954035 Review
- Q&A: How to Drill Through Carpeted Bunk Boards on Boat Trailer Without Shredding Carpeting
- Video: etrailer Trailer Jack JWK-8P Review
- Q&A: Shelby Jack Model 5856A Replacement Recommendation on Jet Ski Trailer
- Video: Review of Fulton Trailer Jack - Side Frame Mount Jack - FXP10W0301
- Video: Fulton Trailer Jack - Side Frame Mount Jack - F1411300301 Review
- Video: Review of Fulton Trailer Jack - Weld On Sidewind Marine Jack - FXP100W0301