2007 Dodge Ram 3500 Class V Hitch Options from Curt

Question

Question:

The definition says Dodge ram pickup. Is the frame the same on a 3500?

asked by: Larry V

0

Expert Reply:

The Curt hitch part # C15800 does fit a 2007 Dodge Ram 3500 but only if the vehicle was a Cab and Chassis model which means it was sold without a truck cab and the frame dimensions are 34 inches apart measured from outside to outside.

For a similar Class V hitch for a non-cab and chassis style truck you'd want the part # C15409 which fits if the truck came with a factory hitch or did not come with one. This hitch has capacities of 17,000 lb total trailer weight.

expert reply by: Jameson C

0

Answer 1

In regards to the Curt Trailer Hitch Receiver part #C15704 which is a fit for a 2003 Dodge Ram 3500, the distance from the top of the flange to the top of the hitch cross tube is 6.65" exactly.

view full answer...

Answer 2

Yes, we still offer the Curt hitch part #C15704 that you referenced. This hitch is a fit for your 2005 Dodge Ram 2500 without the factory hitch as well.

view full answer...

Answer 3

Thank you for the photo, and while there is a 2-1/2 inch trailer hitch receiver that fits your 2021 Ram 5500 cab & chassis, I checked with the manufacturer, and the TorkLift hitch you mentioned will not fit. So for a 2-1/2 inch hitch, you…

view full answer...

Answer 4

You'll need a hitch for a cab/chassis truck, because they use a narrower frame spread (34 inches outside to outside) than the 3500 pickup. The Curt Class V hitch, part #C15800 is the highest rated hitch we offer for your truck, and would work…

view full answer...

Answer 5

I can definitely dispel any confusion you have. Like the video, I confirmed with Kuat that the total length of the Kuat Hitch Receiver Reducer Sleeve - 2-1/2" to 2" Hitch #KU93VR is 6-1/4" long. I went ahead and attached a diagram that…

view full answer...

Answer 6

It would fit well, the Curt Hitch part #C15800 that you referenced has been confirmed by Curt to fit your 2013 Ram 3500 Cab and Chassis without requiring any welding. You will need to use the hitch as a template and drill 3 holes. Check out the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...